Sale!

2009 Chevrolet Corvette Smart Key Fob Driver 2 PN: 25926480

2009 Chevrolet Corvette Smart Key Fob Driver 2 PN: 25926480

Original price was: 169,00 $.Current price is: 111,99 $.

Color

Clear

SKU: SKU8Uv0X48HjF Categories: Chevrolet, General Motors, Remotes, Shop By Make, Shop By Type, Smart Key Remotes Tags: Aftermarket New, Chevrolet, OEM New, OEM Refurbished Brand: Chevrolet

🚨 Stop! Ensure Compatibility Before Ordering!

Important: Some key fobs may look identical but have different internal components. If there are multiple versions of your key fob, you must verify the part number and FCC ID listed in the specifications to ensure compatibility. If only one option exists for your vehicle, VIN verification is not required.

⚠️ When to Provide Your VIN:

If you’re unsure or if multiple versions exist for your model, we recommend verifying with your VIN. You can enter it in the checkout note field, and we will verify it for you before processing your order.

Specifications

Part Numbers: 25854930 and 25926480

FCC ID: M3N5WY7777A

Buttons:

Frequency: 315 Mhz

Remote Programming: By Transponder

Transponder Programming: Onboard if 1 working exist

Chip ID: PHILIPS ID 46

Battery: CR2032 (included)

Emergency Key: (included)

Programming Procedure #227

To match a new transmitter to your vehicle when you have a recognized transmitter (two recognized transmitters are required for Canadian owners):

The vehicle must be off.
Have the recognized and new, unrecognized transmitters on your person.
Go to the rear of the vehicle and insert the vehicle key into the key cylinder located above the license plate. See Hatch on page 2-14 for more information on the key cylinder.
Open the trunk.
Turn the key five times within five seconds.
The DIC will display READY FOR FOB #X, where X can be 2, 3 or 4.
Place the new, unrecognized transmitter in the glove box transmitter pocket with the buttons facing towards the passengers side.
Once the transmitter is programmed, a beep will sound. The DIC will display READY FOR #X, where X can be 3 or 4, or MAXIMUM NUMBER OF FOBS LEARNED.
Press the Acc. button (ignition switch).

The Canadian immobilizer standard requires Canadian owners to see their dealer/retailer for matching new transmitters when two recognized transmitters are not available. United States owners are permitted to match a new transmitter to their vehicle when a recognized transmitter is not available. The procedure will require three ten minutes cycles to complete the matching process.

The vehicle must be off.
Place the new, unrecognized transmitter in the glove box transmitter pocket with the buttons facing towards the passenger side.
Go to the rear of the vehicle and insert the vehicle key into the key cylinder located above the license plate. See Hatch on page 2-14 for more information on the key cylinder.
Open the trunk.
Turn the key five times within five seconds.
The DIC message will display OFF-ACCESSORY TO LEARN.
Press the Acc. button (ignition switch).
The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
The DIC will display OFF-ACCESSORY TO LEARN again.
Press the Acc. button (ignition switch).
The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
The DIC will display OFF-ACCESSORY TO LEARN again.
Press the Acc. button (ignition switch).
The DIC will read WAIT 10 MINUTES and will count down to zero, one minute at a time.
A beep will sound and the DIC will read READY FOR FOB #1. At this time, all previously known transmitters have been erased.
Once the transmitter is recognized and programmed, a beep will sound and the DIC will display READY FOR FOB #2.

If you have additional transmitters to program, take transmitter 1 out of the transmitter pocket and place transmitter 2 in the pocket. This can be done repeatedly until up to four transmitters have be programmed. The DIC will then display MAXIMUM NUMBER OF FOBS LEARNED and will exit the programming mode.

When you are done programming transmitters, press the Acc. button (ignition switch).